Mobile Menu IconMenu
Advanced Embroidery Designs -- Online Center for Machine Embroidery Designs
Easter Sale! 50% OFF EVERYTHING! 3 Days Only! Shop Now!

FSL Battenberg Lace Choker Collar

These are instructions on how to embroider the FSL Battenberg Lace Choker Collar.

The design is for home embroidery machines with a commercial size hoop (8" x 14" or greater). Please note the size of the designs: 232mm x 200mm (8.92" x 7.69") and 359mm x 49mm (13.81" x 1.88").
Besides stabilizer and cotton threads, you will need a clasp 1 1/2"- 2" wide, available in craft stores. Seed beads or crystals are optional. Final assembly is done by hand.

FSL Battenberg Lace Choker Collar image 1

Click to enlarge

Stabilizers: We recommend to use water-soluble mesh, such as Vilene. Vilene D0102 is a non-woven dissolvable stabilizer which is imported into the US, is sold in large rolls and is sometimes packaged under different brand names. Some of these brand names are Fabri-Solvy by Sulky, Avalon Plus by Madeira, Wash-Away, and Aqua Magic.

Film-like water soluble stabilizers, such as Solvy by Sulky, Avalon by Madeira and Badge Master are not suitable for Free-Standing Lace embroidery.

Threads: The thinner the thread, the finer the final product will be. That is why for this project we recommend machine quilting cotton thread, which gives bulk to the lace and makes it look hand-made.

Embroidery polyester thread will make very fine web-like lace.

Embroidery rayon thread is too soft, it does not keep its shape and often its color will fades under the influence of chemicals from the water-soluble mesh.

You can use 40-, 50- or even 60-weight cotton, you can use it both in the bobbin and in the needle. If you use 40-weight cotton thread for the needle, you can use 50- or 60-weight cotton in the bobbin.

We used Signature machine quilting cotton thread both in the needle and in the bobbin, but similar threads from other companies should work just as well.

The drawback of the cotton thread is lint. Please don't forget to clean the machine with a soft bruch or compressed air after each stitch-out.

To get two-sided embroidery, use threads of the same color in the needle and in the bobbin.

Needles: We use size 80/12 embroidery needles and 80/12 metallic needles. Our experience shows that cotton thread used with metallic needles gives less lint. The needles should be sharp, so it's advisable to change them often.

Most Importantly: ALWAYS make a test stitch-out and wash away the stabilizer. This helps you to select the threads, needles, stabilizers and settings of your machine correctly. It's very important to select the correct thread tension!

FSL Battenberg Lace Choker Collar image 2

Washing out the Stabilizer:

Rinsing away the stabilizer is an important step, because the lace can be stretched or distorted if this is done incorrectly. We recommend to use a foam board and stainless pins.

Cut away the excess stabilizer close to the stitches. Take your time and carefully pin every single loop on the lace's outer edge to the board.

Now place the board into a bowl with luke-warm water. Leave the board in the water for at least half an hour. Change the water a couple of times.

Take the board out of the water and leave to air dry. Do not unpin the lace until it's completely dry.

FSL Battenberg Lace Choker Collar image 3

This stitch-out is not a part of the set. It's used for demonstation purposes only.

Choker Collar:

Embroider both files. Wash away the stabilizer, let the designs dry.

FSL Battenberg Lace Choker Collar image 4

Find the center on the lace strip. Thread a sewing needle with the same thread with which you made the embroidery, start connecting the picots on the lace pieces as shown on the diagram below: going from the center to the left, then coming back to the center and going from the center to the right.

FSL Battenberg Lace Choker Collar image 5

You will get something that looks like this. Remember, the collar is not intended to lay flat at this point.

FSL Battenberg Lace Choker Collar image 6

Put a clasp on the ends of the long lace. Use a clasp with a chain if you need to extend the length of the choker.

You can further decorate the choker with seed beads and/or crystals.

FSL Battenberg Lace Choker Collar image 7

We attached seed pearls:

FSL Battenberg Lace Choker Collar image 8

FSL Battenberg Lace Choker Collar image 9

Click to enlarge

The designs from the choker set can also be used individually. Here the central part of the choker is used as an insert on a blouse:

FSL Battenberg Lace Choker Collar image 10

The long piece can be used as edge lace:

FSL Battenberg Lace Choker Collar image 11

Happy embroidering!

Back to FSL Battenberg Lace Choker Collar.

Mailing List
Enter your e-mail for news, discounts and exclusive special offers.


Find us on Twitter

Special Offers
Bonus design on all orders over $50
Daffodils and Eggs Set

Shop Now!

Announcement
Best Project Contest
The results are in!
Featured Project
Check out our latest project Birds and Blooms Quilted Tablerunner
Tutorials
Never heard of photo stitch? - Check out our What is Photo Stitch? page
Most Popular Designs
|| Home || Shop || Free Designs || New Designs ||
|| Projects || Tutorials || Links || About Us || Contact Us ||
|| Store Policy || Licensing || Accessibility ||

Social Media:

Copyright © Advanced Embroidery Designs. All Rights Reserved.