Mobile Menu IconMenu
Advanced Embroidery Designs -- Online Center for Machine Embroidery Designs
Cyber Monday Sale! 50% OFF EVERYTHING! Shop Now!

Wild Rose Cutwork Lace

These are instructions on how to embroider the Wild Rose Cutwork Lace and
Wild Rose Cutwork Lace for 5" x 7" hoop designs.
The designs can be embroidered as a cutwork insert or an applique.
The set also contains petals for a freestanding flower, which can be added to the lace for an eye-catching 3D effect.

You will need fabric, water soluble mesh and embroidery polyester threads.

On the picture below, there is a stitch-out of the larger design as a cutwork lace.

Wild Rose Cutwork Lace image 1

On the picture below, there is a stitch-out of the smaller design as an applique.

Wild Rose Cutwork Lace image 2

Stabilizers: We recommend to use water-soluble mesh, such as Vilene. Vilene D0102 is a non woven dissolvable stabilizer which is imported into the US, is sold in large rolls and is sometimes repackaged under different brand names. Some of these brand names are Fabri-Solvy by Sulky, Wash-Away, and Aqua Magic.

Film-like water soluble stabilizers, such as Solvy by Sulky or Avalon by Madeira, are not good for the cutwork projects.

Please note, we DO NOT recommend to use rayon embroidery threads with water soluble mesh because its chemicals ruin the thread.

Freestanding Flower

The 3D flower is optional. If you don't want to add it, skip ahead.

For the freestanding flower you can use organza, organdy or any other fine fabric. It doesn't have to be sheer, but we think sheer fabrics look best.

Hoop organza with a layer of water soluble mesh. Embroider the files with petals.
Cut out the petals. Wash away the stabilizer. Place the two sets of petals one over another.

Wild Rose Cutwork Lace image 3

Cutwork Insert with or without Applique

Step One: Hoop the fabric with water soluble mesh. Start the machine. It will embroider the outline of the design and stop.

Wild Rose Cutwork Lace image 4

Step Two: If you are making applique, cover the ouline with applique fabric and start the machine.

Wild Rose Cutwork Lace image 5

If you do not want an applique, just start the machine. It will embroider the outline of the whole design, stems and flowers.

Wild Rose Cutwork Lace image 6

Step Three: Take the hoop from the machine.
If you are making applique,
with a pair of sharp scissors cut away the applique fabric around the design and in the areas shown in yellow on the picture- between the leaves, stems and the flower outline.

Then cut out the base fabric in the same area. Take care not to cut through the stabilizer.
Note: You might choose not to cut out the base fabric and have an applique without cutwork. In this case, skip the next step and do not embroider the "bridges".

If you are not using applique fabric, cut the base fabric in the areas shown in yellow on the picture. Do not cut the stabilizer!

Wild Rose Cutwork Lace image 7

Step Four: Return the hoop to the machine and embroider the "bridges".

Wild Rose Cutwork Lace image 8

Step Five: Start the machine again and finish the raw edges of the design.

Wild Rose Cutwork Lace image 9

On the picture below you can see an applique stitch-out without "bridges".

Wild Rose Cutwork Lace image 10

Step Six: If you want to add a 3D flower, pin the petals, as shown to the upper flower of the design and start the machine.

Wild Rose Cutwork Lace image 11

The machine will embroider the center of the flower and fix the petals in place.

Wild Rose Cutwork Lace image 12

Repeat for the lower flower. Wash away the stabilizer, neatly spread on a flat surface and leave to air dry. Press if needed.

Wild Rose Cutwork Lace image 13

Embroidering on Light Jersey Fabrics

As you can see from our pictures, we embroidered the design on a light knit sweater. If you embroider on knits/jersey, you will need additional light-weight cut-away stabilizer under the fabric. We recommend such stabilizers as Soft 'n Sheer, or Soft 'n Sheer Extra by Sulky, No Show Nylon Mesh or Diamond Mesh by Floriani, No Show Fusible or Iron-on Fusible by Marathon and similar stabilizers by other companies.

Whichever brand you use, we recommend iron-on or fusible stabilizer. It forms one layer with the fabric, which makes it easier to do the cutwork. If your stabilizer does not have an adhesive surface, use a temporary fabric adhesive.
You can read about how to embroider the Wild Rose Cutwork design on a T-shirt or a light sweater on the project page.

Wild Rose Cutwork Lace image 14

Happy Embroidering!

Back to Wild Rose Cutwork Lace

Back to Wild Rose Cutwork Lace for 5" x 7" hoop

Mailing List
Enter your e-mail for news, discounts and exclusive special offers.


Find us on Twitter

Special Offers
Bonus design on all orders over $50
12 Days of Christmas Set

Shop Now!

Announcement
Best Project Contest
The results are in!
Featured Project
Check out our latest project Birds and Blooms Quilted Tablerunner
Tutorials
Never heard of photo stitch? - Check out our What is Photo Stitch? page
Most Popular Designs
|| Home || Shop || Free Designs || New Designs ||
|| Projects || Tutorials || Links || About Us || Contact Us ||
|| Store Policy || Licensing || Accessibility ||

Social Media:

Copyright © Advanced Embroidery Designs. All Rights Reserved.